Global options:

-h --help

This help

--config [~/]<path to config file>

Give a config file to use. If it starts with '~/', path is at home dir. Each line in config file is one option, '-' or '--' must not be given! Default: '~/.osmocom/analog/nmt.conf'

--no-config

Even if a config file exists, don't use it.

-v --verbose <level> | <level>,<category>[,<category>[,...]] | list

Use 'list' to get a list of all levels and categories. Verbose level: digit of debug level (default = '3') Verbose level+category: level digit followed by one or more categories -> If no category is specified, all categories are selected

-v --verbose date

Show date with debug output

-k --kanal <channel>

-k --channel <channel>

Channel (German = Kanal) number of "Sender" (German = Transceiver)

-a --audio-device hw:<card>,<device>[/hw:<card>.<rec-device>]

Sound card and device number (default = 'hw:0,0') You may specify a different recording device by using '/'. Don't set it for SDR!

-s --samplerate <rate>

Sample rate of sound device (default = '48000')

-i --interval 0.1..25

Interval of processing loop in ms (default = '1.0' ms) Use 10 to drastically reduce CPU usage. In case of buffer underrun, increase buffer accordingly.

-b --buffer <ms>

How many milliseconds are processed in advance (default = '50') A buffer below 10 ms requires low interval like 0.1 ms.

-p --pre-emphasis

Enable pre-emphasis, if you directly connect to the oscillator of the transmitter. (No pre-emphasis done by the transmitter.)

-d --de-emphasis

Enable de-emphasis, if you directly connect to the discriminator of the receiver. (No de-emphasis done by the receiver.)

--rx-gain <dB>

Raise/lower receiver's RX level by given gain in dB. (Works with sound card only.)

--tx-gain <dB>

Raise/lower transmitters's RX level by given gain in dB. (Works with sound card only.)

-e --echo-test

Use echo test, to send back audio from mobile phone's microphone to the speaker. (German: 'Blasprobe').

-c --call-device hw:<card>,<device>[/hw:<card>.<rec-device>]

Sound card and device number for headset (default = '') You may specify a different recording device by using '/'.

--call-samplerate <rate>

Sample rate of sound device for headset (default = '48000')

--call-buffer <ms>

How many milliseconds are processed in advance (default = '50')

-x --osmocc-cross

Enable built-in call forwarding between mobiles. Be sure to have at least one control channel and two voice channels. Alternatively use one combined control+voice channel and one voice channels.

-o --osmocc-sock

Disable built-in call control and offer socket

--cc "<osmo-cc arg>" [--cc ...]

Pass arguments to Osmo-CC endpoint. Use '-cc help' for description.

--no-l16

Disable L16 (linear 16 bit) codec.

-t --tones 0 | 1

Connect call on setup/release to provide classic tones towards fixed network (default = '1')

-l --loopback <type>

Loopback test: 1 = internal | 2 = external | 3 = echo

-r --realtime <prio>

Set prio: 0 to disable, 99 for maximum (default = 0)

--fast-math

Use fast math approximation for slow CPU / ARM based systems.

--write-rx-wave <file>

Write received audio to given wave file.

--write-tx-wave <file>

Write transmitted audio to given wave file.

--read-rx-wave <file>

Replace received audio by given wave file.

--read-tx-wave <file>

Replace transmitted audio by given wave file.

--limesdr

Auto-select several required options for LimeSDR

--limesdr-mini

Auto-select several required options for LimeSDR Mini

SDR options:

--sdr-soapy

Force SoapySDR driver

--sdr-channel <channel #>

Give channel number for multi channel SDR device (default = 0)

--sdr-device-args <args>

--sdr-stream-args <args>

--sdr-tune-args <args>

Optional SDR device arguments, separated by comma e.g. --sdr-device-args <key>=<value>[,<key>=<value>[,...]]

--sdr-samplerate <samplerate>

Sample rate to use with SDR. By default it equals the regular sample rate.

--sdr-lo-offset <Hz>

Give frequency offset in Hz to move the local oscillator away from the target frequency. (default = -1000000)

--sdr-bandwidth <bandwidth>

Give IF filter bandwidth to use. If not, sample rate is used.

--sdr-rx-antenna <name>

SDR device's RX antenna name, use 'list' to get a list

--sdr-tx-antenna <name>

SDR device's TX antenna name, use 'list' to get a list

--sdr-clock-source <name>

SDR device's clock sourc name, use 'list' to get a list

--sdr-rx-gain <gain>

SDR device's RX gain in dB (default = 0.0)

--sdr-tx-gain <gain>

SDR device's TX gain in dB (default = 0.0)

--write-iq-rx-wave <file>

Write received IQ data to given wave file.

--write-iq-tx-wave <file>

Write transmitted IQ data to given wave file.

--read-iq-rx-wave <file>

Replace received IQ data by given wave file.

--read-iq-tx-wave <file>

Replace transmitted IQ data by given wave file.

--sdr-swap-links

Swap RX and TX frequencies for loopback tests over the air.

--sdr-timestamps 1 | 0

Use TX timestamps on UHD device. (default = 1)

Network specific options:

-N --nmt-system 450/900

Give NMT type as first parameter. (default = '450') Note: This option must be given at first!

-T --channel-type <channel type> | list

Give channel type, use 'list' to get a list. (default = 'CC/TC')

-P --ms-power <power level>

Give power level of the mobile station 0..3. (default = '1') NMT-450: 3 = 15 W / 7 W (handheld), 2 = 1.5 W, 1/0 = 150 mW Note: Power level < 2 causes mobile to search longer for a cell.

-Y --traffic-area <traffic area> | list

NOTE: MUST MATCH WITH YOUR ROAMING SETTINGS IN THE PHONE!

Your phone will not connect, if country code is different!

Give short country code and traffic area separated by comma. (Example: Give 'SE,1' for Sweden, traffic area 1) Add '!' to force traffic area that is not supported by country. (Example: Give 'B,12!' for Belgium, traffic area 12) Use 'list' to get a list of available country code names

-A --area-number <area no> | 0

Give area number 1..4 or 0 for no area number. (default = '0')

-C --compandor 1 | 0

Make use of the compandor to reduce noise during call. (default = '1')

-0 --supervisory 1..4 | 0

Use supervisory signal 1..4 to detect loss of signal from mobile station, use 0 to disable. (default = '1')

-S --smsc-number <digits>

If this number is dialed, the mobile is connected to the SMSC (Short Message Service Center). (default = '767')

-I --caller-id 1 | 0

If set, the caller ID is sent while ringing the phone. (default = '0')

-U --clock 1 | 0

If set, the current time is transmitted with CC. (default = '0') Note that this works only with pure CC, not with combined CC+TC.

station_id: Give 7 digits of station ID,

so you don't need to enter it for every start of this application. Give 7 digits for NMT number (1st digit country code).

Press digits '0'..'9' and then 'd' key to dial towards mobile station. Press 'h' key to hangup. Press 'w' key to toggle display of RX wave form. Press 'c' key to toggle display of channel status. Press 'm' key to toggle display of measurement value. Press 'q' key to toggle display of RX I/Q vector. Press 's' key to toggle display of RX spectrum. Press 'b' key to remove DC level.